A common way to stabilize high rise buildings is to use an elevator core built of concrete. Today, we use to build these elevator cores of in-situ concrete. Precast concrete twin wall (double wall) is a semi-finished product that has become more common in recent years. This diploma work studies how the twin wall works out as structural elements in an elevator core. The work also shows some possible ways of designing twin walls and highlights some important parts of the design that will be vital to the stability of the building.    The result shows that it is important to think through where the element joints should be placed.

This report describes the building of a computer model that makes it possible to simulate the thermal climate in a greenhouse. The computer model is built on the physical theory of heat exchange that occur in a greenhouse, such as radiation and convective heat exchange. The model also includes the heat storage that is active in a greenhouse.The computer model is used to simulate the thermal climate in a greenhouse under three periods, winter, spring and summer. It also investigates which effect a Concrete wall has on the thermal climate in a greenhouse. The purpose of putting a Concrete wall in the greenhouse model is to investigate the possibility to store heat during the day and then use this heat when the temperature drops during the night.The result from the simulations shows that a Concrete wall levels the big difference in temperature that normally occurs under a day in a greenhouse.

This is a booklet with information and inspiration about precast retaining walls. The three chapters contain information about concrete as a material, how the surface of the wall can be altered, and a chapter with ideas for a new precast wall. I have obtained information through books, interviews, lectures and fairs. The retaining walls on the market do not correspond to the requirements of the Landscape Architects I have interviewed. I have therefore considered their opinions in the chapter containing my new ideas for new retaining walls.

In our thesis we will compare interior walls, both bearing and non-bearing. All of thewalls analyzed are currently used in production by Skanska Construction, who is alsoour employer/supervisor for the project. The different wall types will be comparedfocusing mainly on time, cost and workability. All of these walls aside from the nonbearingwall are constructed using concrete, either prefabricated or cast on site..

AbstractThis report intends through a case study to investigate if lightweight concrete isappropriate as main material in the outer wall of a seven storey residential building.A technical design is carried out in accordance with the definitions and requirementsfor passive houses, given by FEBY?s1 ?Demand specification for passive houses?.A literature review is also carried out for a comparison between regular bolt wall andlight weight Concrete wall, with a focus on the safety of moisture.The lightweight concrete block used in the report is as a celblock produced by thecompany H+H Sweden AB.The methods used have resulted in compliance with requirements andrecommendations from authorities. Calculations of energy, noise and moisture riskassessment has been carried out.The work has resulted in the conclusion that the lightweight concrete itself is notable to isolate in the extent necessary to obtain chosen U-value of 0,1 W/m2 ° C,without getting to thick. Therefore additional insulation is needed. There are fewrelevant reference objects built with only light weight concrete.

AbstractThis report intends through a case study to investigate if lightweight concrete isappropriate as main material in the outer wall of a seven storey residential building.A technical design is carried out in accordance with the definitions and requirementsfor passive houses, given by FEBY?s1 ?Demand specification for passive houses?.A literature review is also carried out for a comparison between regular bolt wall andlight weight Concrete wall, with a focus on the safety of moisture.The lightweight concrete block used in the report is as a celblock produced by thecompany H+H Sweden AB.The methods used have resulted in compliance with requirements andrecommendations from authorities. Calculations of energy, noise and moisture riskassessment has been carried out.The work has resulted in the conclusion that the lightweight concrete itself is notable to isolate in the extent necessary to obtain chosen U-value of 0,1 W/m2 ° C,without getting to thick. Therefore additional insulation is needed. There are fewrelevant reference objects built with only light weight concrete.

Lime Hempcrete consists of lime, water and hemp and creates an insulating, sound-absorbing, lightweight and environmentally friendly material that can be used in wall, roof and floor structures (Bevan & Woolley 2008). This construction method is not yet developed in Sweden as there has been a ban on the cultivation of the hemp plant. This ban on the cultivation of hemp was removed in 2003, when the material got a boost. You can use it in many different ways and not just in the construction industry (Ahlsten, 2010).In this study we have investigated the possibility to produce prefabricated wall elements of LHC. We have also studied its mechanical properties and dehydration time.

This Master thesis is about a postal- and telegraphic building in Eskilstuna, Sweden. The construction methods for the specific building and buildings in general from the same time are described. The purpose of the report is to describe the loads acting on the building and how it has been built and why it has been rebuilt during the years. After this, possibilities of reconstruction and adaptation for today?s demands can be evaluated.

Moisture damage in buildings is a serious issue that leads to problematic consequences and high economic costs. Despite the knowledge and awareness existing about moisture problems, extensive damager still occurs today. Studies of moisture in the exterior wall constructions shows that the issue if often caused by rain and water intrusion. These kinds of problem result in major costs usually because the companies have to replace the material and structural components and also in some cases tear down large parts of the buildings.The work includes moisture theory and descriptions of four different exterior wall constructions, wood stud wall with plastered facade, exterior wall with wood facade, exterior wall with concrete, and exterior wall with brick facade. Our thesis work describes how the constructions are affected and moisture damage due to water intrusion.

Hudiksvall Municipality will build a new preschool. The goal is that the pre-school should reflect the municipality's environmental goals and meet building regulations. The wall structures that are compared in the report is an insulated wooden frame and a frame of lightweight concrete blocks from H + HWall structures are compared within the areas of U-values, air tightness, thermal storage capacity, fire ratings, moisture, durability, emissions and environment. In these categories the two wall structures will be rated in a scale from 1 to 5 and then the categories are weighted against each other. The weighting is based on Hudiksvall Municipality's assessment of the categories importanse for their final selection.The results of the comparison show that the concrete structure is recommended for the construction of pre-school with 27.55 points against the wooden structures 23.70 points.

This thesis aims to illustrate how environmental impact can be reduced, through the use of lean concrete. It also illustrates how environmental data can be applied to a house through implementation with BIM. In this study a unique concrete structure developed by Swedish Cement and Concrete Research Institute is assessed for environmental impact, by calculating the carbon dioxide equivalents using LCA methodology. The construction is a sandwich element where the concrete is made ??up of three layers.

We have the tradition in Sweden to build villas and houses with a wooden framework. It has become natural for us because we have so much forest in our country. Building with wood has advantages, it is easy to process, but also disadvantages, as it is sensitive to moisture.Finland has long made use of the thermal blocks to build villas. It is a type of bricks that are a bit like a sandwich element, with a core of EPS and concrete on both sides of the core material. The concrete is hollow, so that after the walls has been bricked up you pour concrete into the hollow bricks.The issue of this report is to find out if concrete can be an alternative to wood as framework material in villas.

We have the tradition in Sweden to build villas and houses with a wooden framework. It has become natural for us because we have so much forest in our country. Building with wood has advantages, it is easy to process, but also disadvantages, as it is sensitive to moisture.Finland has long made use of the thermal blocks to build villas. It is a type of bricks that are a bit like a sandwich element, with a core of EPS and concrete on both sides of the core material. The concrete is hollow, so that after the walls has been bricked up you pour concrete into the hollow bricks.The issue of this report is to find out if concrete can be an alternative to wood as framework material in villas.

This report aims to examine the design of a passive house. The design addresses the selection ofmaterial, sizing and selection of both building services systems and building technical features suchas load-bearing framework and moisture control. Interior layout is designed for a family of twoadults and one child.A big part of the report is devoted to an in-depth comparison of three different wall constructions ofpassive house standard. The structures that have been compared are a lightweight timber structure, aheavier concrete structure and a sandwich wall of the brand Weber Leca. The report covers variousaspects such as air flow, wall thickness, the risks associated with the construction, U-value, thermalbridges, power consumption, price, and assembly costs.

This report aims to examine the design of a passive house. The design addresses the selection ofmaterial, sizing and selection of both building services systems and building technical features suchas load-bearing framework and moisture control. Interior layout is designed for a family of twoadults and one child.A big part of the report is devoted to an in-depth comparison of three different wall constructions ofpassive house standard. The structures that have been compared are a lightweight timber structure, aheavier concrete structure and a sandwich wall of the brand Weber Leca. The report covers variousaspects such as air flow, wall thickness, the risks associated with the construction, U-value, thermalbridges, power consumption, price, and assembly costs.